SUBMERSIBLE MIXERS PM 500

Reduction Drive Self Cleaning Propeller

Fluid Mixer PM 500, Fluid Propeller Mixer, Waste Water Works, Balancing Dams, Biological Reactors, Anaerobic Reactors, Aerobic Reactors, Tannery, Abattoirs, Agriculture

Design

The PM Mixer is there to achieve Speeds via Reduction between Fixed Motor Poles.
Speed Reduction is done using Heavy Duty Duplex Roller Chain and Sprockets, that run in a Transfer Case filled with Oil.

The PCD is adjustable by an Off Centre Output Shaft Housing, which is locked into position with a Clamping Ring, once the Chain Tension is Set and then Locked in place.
Low Cost replacement components compared to matching Gears.

Output Shaft Bearing Assembly

Same configuration as the DD 500 Direct Drive Mixer, with a Double Angular Contact Bearing at the Coupling End and a Cup, Cone Taper Roller Bearing on Propeller End.
Bearing configuration prevent failure due to Radial/Axial and Back Thrust generated by the Propeller's Mixing Forces.

Mechanical Shaft Seal

Metal Bellow. Tungsten Carbide / Tungsten Carbide. Viton O-Rings.
Positioned in an Oil filled Chamber and is not in the product being mixed.

Propeller

Two-Blade, Self Cleaning Type. Material 304 or 316L Stainless Steel. Balanced to ISO 1940/1, G6.3.
The Angle and Pitch of the Propeller Blade are altered to meet Mixing and Kw Demand.

Advantage over Direct Drive Mixer

Alternative Speeds can be achieved which is not standard Fixed Motor Poles, thus giving a wider range of mixing capacity.

Disadvantage

A heavier and more bulky unit than the Direct Drive Mixer, as a Transfer Case, Sprockets and Chains are added.
More moving parts require more maintenance.

Motor

The PM Mixer Motor is of Standard Design as in Fluid VX, SC and SH Series.

— Motor Poles: 2, 4, 6, 8, 12.
— Voltage: 380/415, 50Hz; 525/550, 50Hz; 1000/1100, 50Hz.
— Insulation Class: H / 180°C.
— Protection: IP68 @ 30m.
— Start: DOL or Star / Delta.

Materials / Composition

— Top Cover: GG25 Cast Iron.
— Motor Casing: GG25 Cast Iron.
— Transfer Housing: GG25 Cast Iron.
— Out Put Housing: GG25 Cast Iron.
— Clamp Ring: GG25 Cast Iron.
— Bearing Housing: SG40 Cast Iron.
— Rotor Shaft: 431 T.
— Out Put Shaft: 431 T.
— Propeller: 304 Stainless Steel, Option 316L Stainless Steel.
— Fasteners: 304 Stainless Steel.
— O-Rings and Seals: Nitrile.

Applications

— Waste Water Works.
— Balancing Dams.
— Biological Reactors.
— Anaerobic Reactors.
— Aerobic Reactors.
— Tannery.
— Abattoirs.
— Agriculture.

Installation

As with All Fluid Mixers the Standard Lifting Divide is used.
Any installation can be achieved by altering Lifting Device to Suit.

Fluid Mixer PM 500, Fluid Propeller Mixer, Waste Water Works, Balancing Dams, Biological Reactors, Anaerobic Reactors, Aerobic Reactors, Tannery, Abattoirs, Agriculture

Fluid Mixer PM 500: The Angle and Pitch of the Propeller Blade are altered to meet Mixing and Kw Demand.

Fluid Mixer PM 500, Fluid Propeller Mixer, Waste Water Works, Balancing Dams, Biological Reactors, Anaerobic Reactors, Aerobic Reactors, Tannery, Abattoirs, Agriculture

Fluid Mixer PM 500: Two-Blade, Self Cleaning Type.

Fluid Mixer PM 500, Fluid Propeller Mixer, Waste Water Works, Balancing Dams, Biological Reactors, Anaerobic Reactors, Aerobic Reactors, Tannery, Abattoirs, Agriculture

Application: Waste Water Works.

Fluid Mixer PM 500, Fluid Propeller Mixer, Waste Water Works, Balancing Dams, Biological Reactors, Anaerobic Reactors, Aerobic Reactors, Tannery, Abattoirs, Agriculture

Application: Balancing Dams.

Fluid Mixer PM 500, Fluid Propeller Mixer, Waste Water Works, Balancing Dams, Biological Reactors, Anaerobic Reactors, Aerobic Reactors, Tannery, Abattoirs, Agriculture

Application: Biological Reactors.

Fluid Mixer PM 500, Fluid Propeller Mixer, Waste Water Works, Balancing Dams, Biological Reactors, Anaerobic Reactors, Aerobic Reactors, Tannery, Abattoirs, Agriculture

Fluid Mixer PM 500: Waste Water Works.